Hikrobot MV-CIS-330mm-18-91F2M

TDI modes and model neighbours

Long-line monochrome acquisition is the central role of MV-CIS-330mm-18-91F2M. Its CMOS contact image sensor has 23424 × 3 resolution with 14 μm × 14 μm pixels. It can run as 1-Line at up to 81 kHz, or as 2-TDI and 3-TDI at up to 27 kHz. A 2LC fiber connector carries image data, giving the model a clear fit where line length and selectable accumulation mode take precedence over the highest line frequency.

The 23424-pixel line is suited to detailed inspection across broad sheet, film or web paths, while material movement supplies the second image dimension. The operator can select 1-Line for the 81 kHz rate or a TDI mode when the acquisition calls for 2-TDI or 3-TDI sampling at 27 kHz. Camera and always-on light source use separate 24 VDC feeds: typical loads are 23.4 W and 31.8 W respectively. A 12-pin P10 I/O connection provides the machine timing path independently of the two power connectors.

MV-CIS-308mm-06-U0F1M is the faster, shorter-line neighbour: it provides 7360 × 1 acquisition at up to 95.5 kHz through an LC fiber connector and uses 1-Line scanning. MV-CIS-330mm-18-91F2M/package matches this model at 23424 × 3, 81 kHz in 1-Line, 27 kHz in 2-TDI or 3-TDI, and the same 2LC interface. Select the present designation for the MV-CIS-330mm-18-91F2M item, or the /package designation when that exact variant is required.

Specifications

Selection and applications

Wide-path material inspection. TDI line acquisition. High-detail fiber-linked scanning.

Minimum kit: The minimum setup is the MV-CIS-330mm-18-91F2M contact image sensor assembly with its imaging optics and light source, a 2LC fiber cable, separate 24 VDC feeds, and a 12-pin P10 I/O connection.

Nearby in the range: MV-CIS-308mm-06-U0F1M — Prefer it for a 95.5 kHz, 7360 × 1 acquisition path using an LC fiber connector.; MV-CIS-330mm-18-91F2M/package — Choose it when the required designation is the /package item with otherwise matching imaging ratings..

FAQ

How do line rate and scan mode relate on MV-CIS-330mm-18-91F2M?

The maximum is 81 kHz in 1-Line mode. Selecting 2-TDI or 3-TDI changes the listed maximum to 27 kHz. The sensor output remains based on a 23424-pixel line, with the scan configuration determining whether one, two or three sensor lines participate.

What does the 2LC interface require in the machine architecture?

Image data uses a 2LC fiber connector. Power does not travel over that link: the camera and light source each require 24 VDC through their respective 2-pin connectors. Machine I/O is separate again, using a 12-pin P10 connector for camera timing signals.

What power capacity is needed for the camera and illumination feeds?

At 24 VDC, the camera is rated at a typical 23.4 W. The always-on light source is rated at a typical 31.8 W, also at 24 VDC. The two loads have separate 2-pin power connections, so both branches must be sized for their stated duty.

How large is the assembly with and without the light source fitted?

Without the light source, dimensions are 404 mm × 94.5 mm × 136.6 mm. With the light source, they become 404 mm × 94.5 mm × 140.6 mm. The unchanged length and width simplify the comparison; the fitted light source increases the stated third dimension.

Does the /package entry change the imaging performance of this model?

The recorded imaging and electrical characteristics are the same: 23424 × 3, 14 μm pixels, 81 kHz in 1-Line, 27 kHz in 2-TDI or 3-TDI, a 2LC interface and 24 VDC power. The distinction retained here is the exact model designation.