Hikrobot MV-SC6250M-00C-NNN

High-detail smart-camera integration

A 5120 × 5120 monochrome frame, 2.5 × 2.5 µm pixels, and a global-shutter CMOS sensor give MV-SC6250M-00C-NNN its high-detail, motion-aware imaging character. The 1.1-inch sensor runs at up to 20 fps in Mono 8 and connects through Gigabit Ethernet at 1000 Mbit/s. Processing and industrial communication are housed in an IP67 smart-camera body with a C-mount optical interface.

The square image format suits dimensional checks and surface inspection where detail is needed in both axes. Global exposure supports defined capture of indexed or moving parts, subject to exposure and illumination, while 20 fps sets the full-frame cycle limit. Two inputs, two outputs, two configurable I/O points, RS-232, and a light-source output allow the camera to participate directly in triggered equipment. VGA and one USB host connection are available on the separate 17-pin M12 expansion connector.

Selection rests on the model's balance of 5120 × 5120 resolution at 20 fps, monochrome Mono 8 data, C-mount optics, and a sealed IP67 housing. It requires 24 VDC and draws approximately 15 W without an external light source or 45 W with one. The resulting position is a high-detail smart camera for integrated, moderate-rate inspection where local I/O and environmental sealing carry as much weight as the square image format.

Specifications

Selection and applications

High-detail monochrome surface inspection. Global-shutter checks of indexed parts. Integrated multi-I/O machine control.

Minimum kit: Start with the smart camera, a C-mount lens covering the 1.1-inch sensor, a Gigabit Ethernet cable, the required M12 I/O cable, and a 24 VDC supply sized for the applicable 15 W or 45 W load.

Cables and accessories for this model

Compatibility per manufacturer data.

Data cables

ID Ethernet, M12 8-pinSC cables, M12 17-pinGigE

Power

Power

Optics

M12 lenses

Mounting

Camera mounts

All accessory families →

FAQ

What lens format is required for the 1.1-inch monochrome sensor?

The camera uses a C-mount. Select a C-mount lens that covers the 1.1-inch sensor and resolves the 2.5 × 2.5 µm pixel pitch across the 5120 × 5120 image. Check image-circle coverage and resolved detail across the complete square imaging area.

How much image throughput does MV-SC6250M-00C-NNN generate?

The maximum stated acquisition rate is 20 fps at 5120 × 5120 in Mono 8, and the external data interface is Gigabit Ethernet at 1000 Mbit/s. Size the network for the data actually transmitted by the configured smart-camera workflow rather than treating the maximum acquisition rate as a continuous raw-output guarantee.

How does the global shutter support inspection of moving parts?

The CMOS sensor uses a global shutter, so pixels are exposed on the same capture event rather than line by line. This supports geometrically consistent imaging of indexed or moving parts. The required exposure still depends on scene light, while full-resolution acquisition is capped at 20 fps.

What power supply and consumption should the installation provide?

Supply the camera with 24 VDC. Consumption is approximately 15 W without an external light source and approximately 45 W with an external light source. The power path should therefore be sized for the applicable configuration, including the camera's light-source output use.

Which trigger, control, and peripheral connections are built in?

The 17-pin M12 I/O connector provides two inputs, two outputs, two configurable I/O points, one RS-232 connection, and one light-source output. A separate 17-pin M12 female expansion connector carries one VGA and one USB host connection for local peripherals.

What environmental limits apply to this IP67 smart camera?

The enclosure is rated IP67. Operation is specified from 0 °C to 50 °C, storage from –30 °C to 70 °C, and humidity from 20% RH to 95% RH. The housing measures 116.3 × 68.6 × 101.8 mm and weighs approximately 530 g.