Line scan camera · CL081 series
Hikrobot MV-CL081-B0F2M
- Warranty
- 36 months
Fast single-line fiber inspection
A 240 kHz maximum makes MV-CL081-B0F2M the fastest line-rate camera in the lineup. The monochrome CMOS sensor is 8192 × 1 with 7 × 7 μm pixels and operates in 1-Line mode. Image transfer uses a 2LC fiber connector with 1 Link and 2 Link transmission choices. This profile addresses high-speed line acquisition where a single sensor row and an 8192-pixel field are paired with fiber transport.
Dynamic range is 62.3 dB and SNR is 40 dB. Gain selections are 1.0×, 2.0×, 3.0× and 4.0×, while exposure can be adjusted from 3 μs to 10 ms. Digital I/O is not supported. The camera accepts 12 to 24 VDC and consumes 14.7 W. Its M72*0.75 mount has a 12 mm flange back. The 132 × 76 × 55.5 mm housing weighs 600 g, is rated IP40 and works from -20 to 50 °C.
MV-CL081-B0F2M prioritizes speed over line length relative to MV-CL161-B1Y4M: the latter doubles resolution to 16384 × 1 and uses CoaXPress-12, but reaches 200 kHz in Mono 8/10. MV-CL162-B0F2M supplies a 16384 × 2 monochrome line with 1-Line and 2-TDI over the same 2LC connector family; its maximum line rate is 105 kHz. For Ethernet rather than fiber, MV-CL084-B1NM retains 8192-pixel width, adds 2-TDI and 4-TDI, and reaches 75.6 kHz peak over 2.5 Gigabit Ethernet.
Specifications
| Sensor type | CMOS |
| Resolution | 8192 × 1 px |
| Pixel size | 7 × 7 μm |
| Mono color | Mono |
| Dynamic range | 62.3 dB |
| Exposure time | 3 μs to 10 ms |
| Gain | 1.0×, 2.0×, 3.0×, 4.0× |
| SNR | 40 dB |
| Data interface | 2LC fiber connector |
| Digital I/O | Not supported |
| Lens mount | M72*0.75 |
| Power supply | 12 to 24 VDC |
| Power consumption | 14.7 W |
| Ingress protection | IP40 |
| Operating temperature | -20 to 50 °C |
| Humidity | 5 to 90 % RH |
| Dimensions | 132 × 76 × 55.5 mm |
| Weight | 600 g |
| Compatibility | XoFLink, GenICam |
| Image mode | 1-Line |
| Max line rate | 240 kHz |
| Transmission mode | 1 Link, 2 Link |
| Flange back length | 12 mm |
Selection and applications
High-speed monochrome web inspection. 8192-pixel capture at 240 kHz. Two-link fiber line acquisition.
Minimum kit: Pair MV-CL081-B0F2M with an M72*0.75 lens covering its 8192-pixel line, a cable for the 2LC fiber connector, and a separate 12 to 24 VDC source.
Nearby in the range: MV-CL161-B1Y4M — Prefer it for a 16384 × 1 line at up to 200 kHz over CoaXPress-12.; MV-CL162-B0F2M — Prefer it when 16384 × 2 resolution and 2-TDI are needed on 2LC fiber.; MV-CL084-B1NM — Prefer it for 8192 × 4 monochrome acquisition over 2.5 Gigabit Ethernet..
Cables and accessories for this model
Compatibility per manufacturer data.
- Power
- Power
- Mounting
- Camera mounts
FAQ
What sensor mode produces the 240 kHz MV-CL081-B0F2M rate?
The camera is specified as an 8192 × 1 monochrome CMOS device using 1-Line acquisition. Its maximum line rate is 240 kHz, carried through a 2LC fiber connector.
Which transmission choices are available on MV-CL081-B0F2M?
The fiber interface supports 1 Link and 2 Link transmission modes through the 2LC connector. The receiving side must therefore be arranged for the selected link count and the 240 kHz maximum.
How can exposure and gain be adjusted on MV-CL081-B0F2M?
Exposure spans 3 μs to 10 ms. Four gain values are listed: 1.0×, 2.0×, 3.0× and 4.0×, alongside a 62.3 dB dynamic range and 40 dB SNR. The stated SNR is 40 dB.
Does the MV-CL081-B0F2M connection expose digital I/O?
Digital I/O is not supported. Image data uses the 2LC fiber connector, while camera power is supplied separately at 12 to 24 VDC for a stated consumption of 14.7 W.
What mounting provisions apply to the MV-CL081-B0F2M housing?
The camera uses an M72*0.75 lens mount with a 12 mm flange back. Its 132 × 76 × 55.5 mm, 600 g housing is rated IP40 and operates from -20 to 50 °C at 5 to 90 % RH.