Line scan camera · CL162 series
Hikrobot MV-CL162-B0F2M
- Warranty
- 36 months
105 kHz full-width fiber positioning
Full-width 105 kHz monochrome capture is the distinguishing point of MV-CL162-B0F2M. The CMOS sensor is 16384 × 2 with 3.5 × 3.5 μm pixels and offers 1-Line plus 2-TDI acquisition. Transmission can use 1 Link or 2 Link through a 2LC fiber connector. This combination targets long-line surface inspection where 16384-pixel coverage, row integration and a six-figure line rate are needed together.
The exposure interval spans 3 μs to 10 ms. Dynamic range is 61.7 dB and SNR is 39.4 dB. A 12 to 24 VDC source supplies the camera, which consumes 13.2 W. The optical interface is M72*0.75 with a 12 mm flange back. Housing dimensions are 132 × 76 × 55.5 mm, mass is 600 g and protection is IP40. Rated operation extends from -20 to 50 °C at 5 to 90 % RH.
MV-CL162-B0F2M raises maximum line rate from the 73.2 kHz of MV-CL162-91F2M while retaining 2LC fiber, 1 Link or 2 Link operation and 1-Line or 2-TDI modes. MV-CL162-91F1M is the single-LC variant; its standard 1-Line rate is 73.2 kHz, but ROI reaches 120 kHz at 9984 pixels or below. MV-CL161-B1Y4M changes to a 16384 × 1 sensor and CoaXPress-12, reaching 200 kHz in Mono 8/10.
Specifications
| Sensor type | CMOS |
| Resolution | 16384 × 2 px |
| Pixel size | 3.5 × 3.5 μm |
| Mono color | Mono |
| Dynamic range | 61.7 dB |
| Exposure time | 3 μs to 10 ms |
| SNR | 39.4 dB |
| Data interface | 2LC fiber connector |
| Lens mount | M72*0.75 |
| Power supply | 12 to 24 VDC |
| Power consumption | 13.2 W |
| Ingress protection | IP40 |
| Operating temperature | -20 to 50 °C |
| Humidity | 5 to 90 % RH |
| Dimensions | 132 × 76 × 55.5 mm |
| Weight | 600 g |
| Compatibility | XoFLink, GenICam |
| Image mode | 1-Line, 2-TDI |
| Max line rate | 105 kHz |
| Transmission mode | 1 Link, 2 Link |
| Flange back length | 12 mm |
Selection and applications
Full-width inspection at 105 kHz. 16384-pixel 2-TDI acquisition. Dual-link monochrome fiber scanning.
Minimum kit: Combine MV-CL162-B0F2M with an M72*0.75 lens, a cable for the 2LC fiber connector, and a 12 to 24 VDC source sized for the stated 13.2 W draw.
Nearby in the range: MV-CL162-91F2M — Choose it when 73.2 kHz is sufficient and four configurable I/O lines are required.; MV-CL162-91F1M — Choose it for a single LC interface and a 120 kHz reduced-width ROI option.; MV-CL161-B1Y4M — Choose it for single-line CoaXPress-12 capture at up to 200 kHz..
Cables and accessories for this model
Compatibility per manufacturer data.
- Power
- Power
- Mounting
- Camera mounts
FAQ
What sensor modes accompany the 105 kHz MV-CL162-B0F2M maximum?
The 105 kHz maximum accompanies a 16384 × 2 monochrome CMOS sensor with 1-Line and 2-TDI acquisition. Transmission can use either 1 Link or 2 Link through the 2LC fiber connector.
Which fiber transmission modes are offered by MV-CL162-B0F2M?
The 2LC fiber connector supports both 1 Link and 2 Link transmission. The receiving interface should be selected for that link arrangement and the camera's 105 kHz maximum.
What imaging controls are stated for MV-CL162-B0F2M?
Exposure is adjustable from 3 μs to 10 ms. The 16384 × 2 monochrome CMOS sensor lists 61.7 dB dynamic range and 39.4 dB SNR at a 3.5 × 3.5 μm pixel size.
How should MV-CL162-B0F2M be powered and mounted optically?
The camera accepts 12 to 24 VDC and consumes 13.2 W. It uses an M72*0.75 lens mount with a 12 mm flange back for optics covering the 16384-pixel line.
What environmental range surrounds MV-CL162-B0F2M operation?
The IP40 body is rated from -20 to 50 °C and 5 to 90 % RH. It measures 132 × 76 × 55.5 mm and weighs 600 g, setting the mechanical load for the mount.