Line scan camera · CL Series
Hikrobot MV-CL083-B0F2C
- Warranty
- 36 months
A 71 kHz 8K color fiber variant
A 71 kHz full-width color line distinguishes MV-CL083-B0F2C among the 8192 × 3 models. The CMOS sensor uses 7 × 7 µm pixels, 1-Line scanning and a 2LC fiber interface. Its exposure range is 3 µs to 10 ms, dynamic range is 61.2 dB, and gain steps of 1.0×, 2.0×, 3.0× and 4.0× provide optical-level adjustment.
This model addresses wide color surface inspection where the acquisition timing is handled outside the camera I/O, because digital I/O is not supported. The 2LC fiber path carries the image stream, while the camera takes 12 V DC to 24 V DC and draws a typical 15.8 W at 12 V DC. The body measures 132 mm × 76 mm × 55.5 mm and uses an M72*0.75 lens interface.
MV-CL083-91F2C uses the same 8192 × 3 color geometry and 2LC transport, reaches 66.6 kHz and adds four configurable I/O lines on a 12-pin P10 connector. MV-CL083-92CC changes to Camera Link, reaching 33.7 kHz at full width or 66.6 kHz at 4140 pixels and below. MV-CL084-B1NC uses 2.5 Gigabit Ethernet and runs at 37.6 kHz in full-resolution Mono 8/Bayer RG 8.
Specifications
| Product type | 8192 px Fiber Line Scan Camera |
| Sensor type | CMOS |
| Resolution | 8192 × 3 |
| Pixel size | 7 μm × 7 μm |
| Mono color | Color |
| Dynamic range | 61.2 dB |
| Exposure time | 3 μs to 10 ms |
| Gain | 1.0 ×, 2.0 ×, 3.0 ×, 4.0 × |
| Data interface | 2LC fiber interface |
| Digital I/O | Not supported |
| Lens mount | M72*0.75, flange back length 12 mm, applicable to F-mount via lens adapter |
| Power supply | 12 VDC to 24 VDC |
| Power consumption | Typ. 15.8 W @ 12 VDC |
| Ingress protection | IP40 (under proper lens installation and wiring) |
| Operating temperature | –20 °C to 50 °C (–4 °F to 122 °F) |
| Storage temperature | –30 °C to 80 °C (–22 °F to 176 °F) |
| Humidity | 5% RH to 90% RH (no condensation) |
| Dimensions | 132 mm × 76 mm × 55.5 mm (5.2″ × 3.0″ × 2.2″) |
| Weight | Approx. 600 g (1.3 lb.) |
| Certification | CE-EMC, KC |
| Compatibility | XoFLink, GenICam |
| Max line rate | 71 kHz |
| Line length | 8192 |
| Scan type | 1-Line |
Selection and applications
8K color scanning at 71 kHz. Dual-fiber wide-surface inspection. Color acquisition without camera I/O.
Minimum kit: Use the MV-CL083-B0F2C camera, an M72*0.75 line-scan lens or adapted F-mount optic, a 2LC fiber cable and receiver, and a 12 V DC to 24 V DC supply.
Nearby in the range: MV-CL083-91F2C — Prefer it when the 2LC color camera must provide four configurable I/O lines.; MV-CL083-92CC — Prefer it when the acquisition system is based on Camera Link.; MV-CL084-B1NC — Prefer it for 2.5 Gigabit Ethernet transport and a 76 mm body width..
Cables and accessories for this model
Compatibility per manufacturer data.
- Power
- Power
- Mounting
- Camera mounts
FAQ
Does MV-CL083-B0F2C provide trigger or general-purpose digital I/O?
No. The digital I/O entry states that it is not supported. The integration must therefore account for acquisition coordination outside a camera I/O connection while receiving the 8192 × 3 color stream over the 2LC fiber interface.
What is the maximum full-line rate of MV-CL083-B0F2C?
The stated maximum is 71 kHz for the 8192 × 3 color CMOS sensor in 1-Line operation. Pixel pitch is 7 × 7 µm, exposure ranges from 3 µs to 10 ms and selectable gains extend from 1.0× to 4.0×.
Which optics attach to the MV-CL083-B0F2C housing?
The native thread is M72*0.75 with a 12 mm flange back length. F-mount optics may be fitted through an adapter, with coverage selected for the complete 8192-pixel color line and resolution appropriate to 7 µm pixels.
How should power be sized for an MV-CL083-B0F2C station?
The supply range is 12 V DC to 24 V DC and typical consumption is 15.8 W at 12 V DC. Image data uses the separate 2LC fiber interface, and the power design should not assume camera-side digital I/O because that function is unsupported.
What environmental limits apply to MV-CL083-B0F2C?
The camera operates from -20 °C to 50 °C at 5% RH to 90% RH without condensation and stores from -30 °C to 80 °C. IP40 applies with proper lens installation and wiring, so liquid and substantial dust require external protection.