Line scan camera · CL Series
Hikrobot MV-CL162-91F1M
- Lead time
- from 5 days
- Warranty
- 36 months
Fiber scanning at full width and by ROI
Single-LC fiber transport and a 16384 × 2 monochrome sensor define MV-CL162-91F1M. Its CMOS pixels measure 3.5 µm × 3.5 µm, and the camera supports 1-Line and 2-TDI acquisition. Standard operation reaches 73.2 kHz in 1-Line mode and 60 kHz in 2-TDI. ROI can raise 1-Line capture to 120 kHz when the active width is 9984 pixels or below, supporting inspection that trades covered line width for acquisition rate.
The optical connection is M72*0.75 with a 12 mm flange-back distance, and an adapter permits F-mount lens use. Image data uses the LC fiber interface. The housing is 132 mm × 76 mm × 57.4 mm, which must be allowed for along the optical axis and in the camera support. With its two scan modes and explicit ROI rate, the model can be configured either for full 16384-pixel coverage or for a shorter, faster region.
Against MV-CL162-91CM, this model changes the transport from SDR Camera Link to LC fiber; the Camera Link version reaches 50 kHz in 80-bit mode and 120 kHz by ROI at 6820 pixels or below. MV-CL162-91F2M uses a 2LC connector and states 1 Link and 2 Link transmission at up to 73.2 kHz. MV-CL162-B0F2M keeps the 2LC fiber arrangement but raises maximum line rate to 105 kHz and adds a 3 µs to 10 ms exposure range.
Available versions
One device, different revisions. We ship the current one by default; if a specific revision is already installed on your line, name it in the request and we will match it.
| Part number | PN | Version | |
|---|---|---|---|
| MV-CL162-91F1M | 306303800 | — | |
| MV-CL162-91F1M V2.0 | 306303885 | V2.0 |
Specifications
| Maximum line rate | 73200 Hz @ 1-line, base line rate; 60000 Hz @ 2-line TDI, base line rate; 120000 Hz @ 1-line, in ROI mode, ROI width up to 9984 px |
| Line/TDI image mode | single line, 2-TDI |
| Color mode | mono |
| Data interface | XoFLink |
| Sensor technology | CMOS |
| Pixel size | 3.5×3.5 µm1 |
| Dynamic range | 62 dB |
| Signal-to-noise ratio | 39.2 dB |
| Exposure time | 3…10000 µs |
| Auto exposure | Auto, Off, Once, trigger width |
| Linear gain factor | 1 |
| Pixel format | Mono8, Mono10, Mono12 |
| Binning | 1x1, 1x2, 1x4, 2x1, 2x2, 2x4, 4x1, 4x2, 4x4 |
| Trigger mode | external, internal; line, frame, line and frame @ external trigger |
| Flange focal distance | 12 mm |
| Data interface connector | LC |
| Protocol compatibility | XoFLink, GenICam |
| Client software | MVS |
| Operating systems | Windows 7 (32/64-bit), Windows 10 (32/64-bit), Windows 11 (64-bit) |
| Digital I/O lines | 4 bidirectional lines, single-ended, differential, lines 0, 1, 3, 4 |
| Digital I/O connector | P10 12-pin |
| Power consumption | 10.6 W (typical) @ DC, supply voltage 24 V |
| Ingress protection | IP40 @ with lens and cables properly installed |
| Working temperature | -20…50 °C |
| Storage temperature | -30…80 °C |
| Humidity | 5…90 % @ non-condensing |
| Dimensions | 132×76×57.4 mm |
| Weight | 600 g (approx.) |
| Certification | CE, RoHS, KC |
| Mounts via adapter | F-mount (via adapter) |
| Transmission mode | one link |
| Power supply connector | P10 12-pin |
| Reverse image | horizontal |
| Part number | Sensor resolution | Lens mount | Power supply |
|---|---|---|---|
| MV-CL162-91F1M V2.0 | 16384×2 px | M72×0.75 | 12…24 V |
| MV-CL162-91F1M | 16384 px1 | F-mount; M721 | 12…24 V @ DC |
1 unofficial data
Selection and applications
Single-fiber 16384-pixel inspection. 2-TDI monochrome surface scanning. Reduced-width capture at 120 kHz.
Minimum kit: Use MV-CL162-91F1M with an M72*0.75 lens or adapted F-mount lens, an LC fiber cable, and camera power provision for the installation.
Nearby in the range: MV-CL162-91CM — Choose it when the 16384 × 2 monochrome acquisition chain must use Camera Link; MV-CL162-91F2M — Choose it for 2LC fiber transmission with selectable 1 Link and 2 Link modes; MV-CL162-B0F2M — Choose it when the same resolution and scan modes require a 105 kHz maximum.
Cables and accessories for this model
Compatibility per manufacturer data.
- Power
- Power
- Mounting
- Camera mounts
FAQ
What are the standard full-width rates for MV-CL162-91F1M?
At standard operation, 1-Line acquisition is rated at 73.2 kHz and 2-TDI at 60 kHz. Both modes use the camera's 16384 × 2 monochrome CMOS sensor and LC fiber data interface.
When can MV-CL162-91F1M reach its 120 kHz ROI rate?
The 120 kHz figure applies to 1-Line acquisition after ROI is reduced to 9984 pixels or below. It is therefore an active-width trade against the full 16384-pixel line.
Which cable interface carries images from MV-CL162-91F1M?
Image transmission is through an LC fiber interface. This distinguishes the model from MV-CL162-91CM, which uses an SDR Camera Link connector while keeping the same 16384 × 2 monochrome resolution.
How can an F-mount lens be attached to MV-CL162-91F1M?
The camera's native mount is M72*0.75 and the flange-back distance is 12 mm. An F-mount lens may be used through an adapter, with optical coverage selected for the 16384-pixel line.
What space should be reserved for the MV-CL162-91F1M housing?
The stated housing dimensions are 132 mm × 76 mm × 57.4 mm. This is longer than the 76 mm × 76 mm × 42.1 mm MV-CL162-91CM body and should be reflected in the mechanical layout.