Hikrobot MV-CH1510-10XM-M72-NF

Applications and position in the range

Resolving fine monochrome detail across a large image is the defining role of the Sony IMX411 in this model. Its 14208 × 10640 output, 3.76 × 3.76 µm pixels and 78.7 dB dynamic range support close examination of stationary surfaces and geometry. A rolling shutter and 6.2 fps acquisition rate favour controlled scenes, while CoaXPress with a DIN interface carries the image stream.

The camera suits dimensional inspection, surface-feature mapping and archival capture when the object can remain still through the exposure. Exposure can be set from 15 µs to 10 sec, allowing the imaging sequence to be coordinated with continuous or pulsed illumination. Monochrome capture keeps the measurement based on intensity, and the M72*0.75 mount addresses the large image circle required by the sensor.

Within this group, MV-CH1510-11XM-M72-TF retains the same sensor, resolution and 6.2 fps rate but uses a 120 × 120 × 84.6 mm body and a cooling operating point. MV-CH2450-10YM-M72-TF raises resolution to 19200 × 12800 and speed to 12.4 fps through HDBNC CoaXPress. MV-CH1520-90GM-M72-NN is the M72 alternative for global-shutter capture over Gigabit Ethernet, though its uncompressed rate is 0.8 fps.

Specifications

Selection and applications

Large-area monochrome detail capture. Stationary surface-feature inspection. Dimensional imaging with controlled exposure.

Minimum kit: Use the camera with an M72*0.75 lens, a DIN-interface CoaXPress cable and a 12 to 24 V DC power supply.

Nearby in the range: MV-CH1510-11XM-M72-TF — Choose it for the same 14208 × 10640 imaging format with the listed cooling operating point.; MV-CH2450-10YM-M72-TF — Choose it when 19200 × 12800 resolution and 12.4 fps are required.; MV-CH1520-90GM-M72-NN — Choose it for an M72 camera with global shutter and Gigabit Ethernet..

Cables and accessories for this model

Compatibility per manufacturer data.

Data cables

CoaXPress

I/O & power cables

12-pin IO

Power

Power

Mounting

Camera mounts

All accessory families →

FAQ

What lens interface must be matched to the MV-CH1510-10XM-M72-NF?

The camera uses an M72*0.75 lens mount with a 19.55 mm flange-back length. Select an optic that matches both that mechanical interface and the 14208 × 10640 imaging area; a C-mount or M58 lens cannot be attached as the native lens for this body.

How does the rolling shutter affect inspection timing on this model?

The Sony IMX411 uses a rolling shutter, so different image rows are exposed at different times. For geometric measurement or fine surface inspection, hold the object still or coordinate the 15 µs to 10 sec exposure with illumination and object motion to limit spatial distortion.

What host connection is required for its full-resolution image stream?

Image transfer uses CoaXPress through a DIN interface. The acquisition side therefore needs a matching CoaXPress connection and DIN-ended cable. The 6.2 fps maximum rate applies to the 14208 × 10640 output, so processing and storage should be sized for that image stream.

What power and control wiring does the camera require?

Supply the camera with 12 to 24 V DC; typical consumption is 18 W. Control wiring is presented on a 12-pin P10 connector with one opto-isolated input, one opto-isolated output, one bidirectional non-isolated I/O and one RS-232 channel.

Which environmental limits apply to MV-CH1510-10XM-M72-NF?

The listed working range is 0 to 50 °C with 20 to 95 % RH, and the enclosure rating is IP40. The 100 × 100 × 74.3 mm body weighs 1.0 kg, so the installation needs a rigid support and environmental protection consistent with IP40.