Line scan camera · CL Series
Hikrobot MV-CL084-91CM-PRO
- Lead time
- from 5 days
- Warranty
- 36 months
Multi-light 8K imaging with a 16-row array
An 8192 × 16 mono CMOS array and integrated multi-light sequencing set MV-CL084-91CM-PRO apart from every other model in the lineup. Its 5 µm pixels support 1-line, 2-TDI and 4-TDI acquisition plus 2-lamp, 3-lamp or 4-lamp control. With multi-light control disabled or at 1 lamp, Camera Link reaches 20 kHz Base, 40 kHz Medium and 75 kHz Full or 80-bit operation.
Separate illumination states can be captured as a wide target moves past the line. At 2 lamps the maximum reaches 50 kHz in 80-bit mode, at 3 lamps 33 kHz, and at 4 lamps 25 kHz; the rate reduction reflects the added lighting sequence. Exposure is 3 µs to 10 ms, and 1.2×, 2.7× and 4.6× gain settings support adjustment of the monochrome response.
MV-CL084-91CM is the smaller 8192 × 4 Camera Link variant, reaching 100 kHz in 80-bit mode and drawing 9.7 W. MV-CL084-91F2M provides 8192 × 4 over 2LC fiber with up to 4-light control and 200 kHz in 1-Line, 1-light mode. MV-CL084-91Y2M has the same four-row multi-light rate table as that fiber model but transfers through two CXP-10 Micro-BNC interfaces.
Specifications
| Sensor resolution | 8192×16 px |
| Maximum line rate | 20000 Hz @ Base, number of lights (multi-light mode) 1 40000 Hz @ Medium, number of lights (multi-light mode) 1 75000 Hz @ Full, number of lights (multi-light mode) 1 Show all (16)75000 Hz @ 80-bit (Deca), number of lights (multi-light mode) 110000 Hz @ Base, number of lights (multi-light mode) 2 20000 Hz @ Medium, number of lights (multi-light mode) 2 40000 Hz @ Full, number of lights (multi-light mode) 2 50000 Hz @ 80-bit (Deca), number of lights (multi-light mode) 2 6000 Hz @ Base, number of lights (multi-light mode) 3 13000 Hz @ Medium, number of lights (multi-light mode) 3 27000 Hz @ Full, number of lights (multi-light mode) 3 33000 Hz @ 80-bit (Deca), number of lights (multi-light mode) 3 5000 Hz @ Base, number of lights (multi-light mode) 4 10000 Hz @ Medium, number of lights (multi-light mode) 4 20000 Hz @ Full, number of lights (multi-light mode) 4 25000 Hz @ 80-bit (Deca), number of lights (multi-light mode) 4 |
| Line/TDI image mode | single line, 2-TDI, 4-TDI |
| Color mode | mono |
| Lens mount | M72×0.75 |
| Data interface | Camera Link |
| Sensor technology | CMOS |
| Pixel size | 5×5 µm |
| Dynamic range | 57.8 dB |
| Signal-to-noise ratio | 41.3 dB |
| Exposure time | 3…10000 µs |
| Auto exposure | Off, Once, Continuous, fixed exposure time, trigger width |
| Linear gain factor | 1.2; 2.7; 4.6 |
| Pixel format | Mono8, Mono10, Mono12 |
| Binning | 1x1, 1x2, 1x4, 2x1, 2x2, 2x4, 4x1, 4x2, 4x4 |
| Trigger mode | external, internal; line, frame @ external trigger; line, frame @ external trigger, line + frame trigger |
| Flange focal distance | 12 mm |
| Data interface connector | Camera Link SDR |
| Protocol compatibility | Camera Link, GenICam |
| Communication protocol versions | Camera Link 2.0 |
| Third party software protocol | Camera Link |
| Client software | MVS |
| Operating systems | Windows 7 (32/64-bit), Windows 10 (32/64-bit), Windows 11 (64-bit) |
| Digital I/O lines | 4 bidirectional lines, single-ended, differential, lines 0, 1, 3, 4 |
| Power supply | 24 V |
| Power consumption | 22.9 W (typical) @ DC, supply voltage 24 V |
| Ingress protection | IP40 @ with lens and cables properly installed |
| Working temperature | -20…60 °C |
| Storage temperature | -30…80 °C |
| Humidity | 5…90 % @ non-condensing |
| Dimensions | 84×84×89 mm |
| Weight | 900 g (approx.) |
| Certification | CE, RoHS, KC |
| Camera Link configuration | Base, Medium, Full, 80-bit |
| Mounts via adapter | F-mount (via adapter) |
| Camera link control lines | CC1, CC2, CC3, CC4 |
| Pixel clock | 40000000 Hz; 66000000 Hz; 80000000 Hz; 85000000 Hz |
| Port inventory | Camera Link ×2 (data), USB (firmware update) |
| Reverse image | horizontal |
| Supported multi-light count | 2; 3; 4 |
| Tap count | 2; 4; 8; 10 |
| Tap geometry | 1X2, 1X4, 1X8, 1X10 |
Documents
Selection and applications
8K multi-light surface inspection. Sixteen-row mono acquisition. Four-lamp Camera Link scanning.
Minimum kit: Build the station with the MV-CL084-91CM-PRO, an M72*0.75 line-scan lens or adapted F-mount optic, a Camera Link cable and frame grabber, and a 24 V DC supply sized for 22.9 W.
Nearby in the range: MV-CL084-91CM — Prefer it for an 8192 × 4 Camera Link array at up to 100 kHz in 80-bit operation; MV-CL084-91F2M — Prefer it for four-row multi-light acquisition over 2LC fiber; MV-CL084-91Y2M — Prefer it for four-row multi-light acquisition through two CXP-10 links.
Cables and accessories for this model
Compatibility per manufacturer data.
- Data cables
- Camera Link
- I/O & power cables
- 12-pin IO
- Power
- Power
- Mounting
- Camera mounts
FAQ
How does lamp count change MV-CL084-91CM-PRO line rate?
In 80-bit operation the ceiling is 75 kHz with control disabled or 1 lamp, 50 kHz with 2 lamps, 33 kHz with 3 lamps and 25 kHz with 4 lamps. More lighting states therefore reduce the line rate available for each sequence.
Which sensor and scan modes make the PRO version different?
MV-CL084-91CM-PRO uses an 8192 × 16 mono CMOS sensor with 5 µm pixels. It supports 1-line, 2-TDI and 4-TDI as well as 2-lamp, 3-lamp and 4-lamp control, whereas MV-CL084-91CM uses an 8192 × 4 array.
What electrical supply is required by MV-CL084-91CM-PRO?
This model requires 24 V DC and has typical consumption of 22.9 W at 24 V DC. Power and four configurable I/O lines use the 12-pin P10 connector, and the I/O can operate with single-ended or differential signals.
Which lens interface covers the MV-CL084-91CM-PRO line?
The camera provides an M72*0.75 mount with a 12 mm flange back length. F-mount optics may be attached through an adapter, and the lens must cover all 8192 pixels while resolving the 5 µm pitch.
What mechanical and thermal allowance does the PRO housing need?
The body measures 84 mm × 84 mm × 89 mm, weighs about 900 g and operates from -20 °C to 60 °C. Its IP40 rating assumes proper lens installation and wiring, and the typical 22.9 W draw must be included in thermal planning.
Is USB the acquisition path for MV-CL084-91CM-PRO?
No. Image transfer uses Camera Link through an SDR connector. USB is listed for firmware updating. The acquisition system must use a Camera Link cable and receiver able to handle the selected Base, Medium, Full or 80-bit multi-light mode.