Line scan camera · CL Series
Hikrobot MV-CL084-91CM
- Warranty
- 36 months
Four-row 8K mono with Camera Link
An 8192 × 4 mono CMOS array with 5 µm pixels gives MV-CL084-91CM both long cross-object sampling and three row-mode choices. It supports 1-line, 2-TDI and 4-TDI acquisition. Camera Link rates are 20 kHz in Base, 40 kHz in Medium, 80 kHz in Full and 100 kHz in 80-bit operation, with an SDR connector used for data and USB used for firmware updates.
The four-row architecture suits wide mono surface inspection where illumination and travel speed can be addressed through the selected TDI mode. Exposure spans 3 µs to 10 ms and six gain settings run from 1.2× to 6.2×. A 12-pin P10 connector supplies power and four configurable I/O lines, while Camera Link CC1/CC2/CC3/CC4 can also participate in acquisition timing.
MV-CL082-92CM reduces the array to 8192 × 2 with 7 µm pixels and 2-TDI, while retaining the same 100 kHz 80-bit ceiling in a smaller 76 mm body. MV-CL084-91CM-PRO expands to 8192 × 16 and adds control for as many as 4 lamps, with a 75 kHz 1-lamp Full rate. MV-CL084-91F2M keeps 8192 × 4 but uses 7 µm pixels and 2LC fiber, reaching 200 kHz in 1-Line, 1-light mode.
Specifications
| Product type | 8192 px Camera Link Line Scan Camera |
| Sensor type | CMOS |
| Resolution | 8192 × 4 |
| Pixel size | 5 μm |
| Mono color | Mono |
| Dynamic range | 62 dB |
| Exposure time | 3 μs to 10 ms |
| Gain | 1.2 ×, 2.7 ×, 3.0 ×, 3.5 ×, 4.6 ×, 6.2 × |
| Data interface | Camera Link (SDR connector); USB interface for updating firmware |
| Digital I/O | 12-pin P10 connector provides power and I/O: configurable input and output × 4 (Line 0/1/3/4), and support single-end/differential. Camera Link provides I/O (CC1/CC2/CC3/CC4). |
| Lens mount | M72*0.75, flange back length 12 mm, applicable to F-mount via lens adapter |
| Power supply | 12 VDC to 24 VDC |
| Power consumption | Typ. 9.7 W @ 12 VDC |
| Ingress protection | IP40 (under proper lens installation and wiring) |
| Operating temperature | –20 °C to 55 °C (–4 °F to 131 °F) |
| Storage temperature | –30 °C to 80 °C (–22 °F to 176 °F) |
| Humidity | 5% RH to 90% RH (no condensation) |
| Dimensions | 84 mm × 84 mm × 46.2 mm (3.3″ × 3.3″ × 1.8″) |
| Weight | Approx. 476 g (1.0 lb.) |
| Certification | CE-EMC, KC |
| Compatibility | Camera Link V1.2, GenICam |
| Max line rate | 20 kHz (Base), 40 kHz (Medium), 80 kHz (Full), 100 kHz (80-bit) |
| Line length | 8192 |
| Scan type | Supports 1-line, 2-TDI, 4-TDI |
Selection and applications
8K four-row mono inspection. Camera Link 4-TDI scanning. Wide-surface capture at 100 kHz.
Minimum kit: Pair the MV-CL084-91CM camera with an M72*0.75 line-scan lens or adapted F-mount lens, a Camera Link cable and frame grabber, and a 12 V DC to 24 V DC supply on the 12-pin P10 connector.
Nearby in the range: MV-CL082-92CM — Prefer it for an 8192 × 2 sensor in a 76 mm Camera Link body.; MV-CL084-91CM-PRO — Prefer it for an 8192 × 16 array with multi-lamp control.; MV-CL084-91F2M — Prefer it for 8192 × 4 mono capture at 200 kHz over 2LC fiber..
Cables and accessories for this model
Compatibility per manufacturer data.
- Data cables
- Camera Link
- I/O & power cables
- 12-pin IO
- Power
- Power
- Mounting
- Camera mounts
FAQ
Which row modes are supported by the MV-CL084-91CM array?
The 8192 × 4 mono sensor supports 1-line, 2-TDI and 4-TDI modes. Its 5 µm pixels can be read at up to 20 kHz in Base, 40 kHz in Medium, 80 kHz in Full and 100 kHz in 80-bit Camera Link operation.
What gain and exposure controls are available on MV-CL084-91CM?
Exposure is adjustable from 3 µs to 10 ms. Listed gain selections are 1.2×, 2.7×, 3.0×, 3.5×, 4.6× and 6.2×, providing discrete settings for matching the mono sensor response to the illumination arrangement.
How should a lens be mounted on the MV-CL084-91CM?
MV-CL084-91CM has an M72*0.75 interface and a 12 mm flange back length. F-mount lenses can be fitted via an adapter. The optic must cover the full 8192-pixel line and resolve the 5 µm pixel pitch.
What are the MV-CL084-91CM power and I/O provisions?
Provide 12 V DC to 24 V DC through the 12-pin P10 connector and allow for 9.7 W typical consumption at 12 V DC. Four configurable single-ended or differential I/O lines are available, together with Camera Link CC1/CC2/CC3/CC4.
How does MV-CL084-91CM differ from MV-CL084-91CM-PRO?
The standard model uses an 8192 × 4 mono array, reaches 100 kHz in 80-bit mode and draws 9.7 W typically. The PRO version uses 8192 × 16, adds multi-lamp control, takes 24 V DC and draws 22.9 W typically.