Hikrobot MV-CL086-B0F1C

Fiber color acquisition and alternatives

A 40 kHz rate across every image mode gives MV-CL086-B0F1C a clear role in fiber-connected color scanning. The CMOS device has an 8192 × 12 resolution, 5 µm × 5 µm pixels and selectable 1-Line, 2-TDI and 4-TDI acquisition. Image data leaves through an LC fiber interface. The combination is intended for color inspection of moving surfaces where the selected integration mode must not lower the stated maximum line rate.

Exposure spans 3 µs to 10 ms, dynamic range is 63.7 dB and gain settings are 1.0 ×, 1.3 ×, 2.0 × and 4.0 ×. The camera has no digital I/O, so acquisition architecture must account for control separately from the image link. Power is 12 VDC to 24 VDC through the camera connection, with typical consumption of 14.4 W at 12 VDC. Its M72*0.75 mount has a 12 mm flange back and accepts F-mount optics by adapter.

MV-CL086-B0F1C shares its 8192 × 12 color arrangement and 4-TDI option with MV-CL086-91CC-PRO, but replaces Camera Link with LC fiber and runs at 40 kHz in all image modes. MV-CL086-91GC also reaches 40 kHz in high-bandwidth mode over Gigabit Ethernet, though its sensor arrangement is 8192 × 6. For twice the line length, MV-CL166-B0F2C provides 16384 × 12 color capture through a 2LC fiber connector at 40 kHz and uses an M90*1.0 mount.

Specifications

Selection and applications

Fiber-linked 8192-pixel color scanning. Constant-rate 4-TDI surface capture. Color inspection at 40 kHz.

Minimum kit: Combine MV-CL086-B0F1C with an M72*0.75 lens or adapted F-mount optic, an LC fiber cable, and a 12 VDC to 24 VDC power connection.

Nearby in the range: MV-CL086-91CC-PRO — Select it for 8192 × 12 color and 4-TDI acquisition through Camera Link.; MV-CL086-91GC — Select it when Gigabit Ethernet is needed with an 8192 × 6 color arrangement.; MV-CL166-B0F2C — Select it for a 16384 × 12 color line and a 2LC fiber connector at 40 kHz..

Cables and accessories for this model

Compatibility per manufacturer data.

Power

Power

Mounting

Camera mounts

All accessory families →

FAQ

Does changing TDI mode reduce the stated MV-CL086-B0F1C line rate?

The listed maximum is 40 kHz under all image modes. Those modes are 1-Line, 2-TDI and 4-TDI on the 8192 × 12 color CMOS sensor, so the same headline rate applies to each stated choice.

What image and control connections are present on MV-CL086-B0F1C?

Image transmission uses an LC fiber interface. Digital I/O is explicitly not supported, so the station design should treat the fiber connection as the image path and not expect camera-side configurable I/O lines.

Which power range and consumption apply to MV-CL086-B0F1C?

The accepted input range is 12 VDC to 24 VDC. Typical consumption is 14.4 W at 12 VDC, which supplies a concrete load figure for selecting the power source and cable arrangement.

Can an F-mount optic be used with the MV-CL086-B0F1C mount?

Yes. The native thread is M72*0.75 with a 12 mm flange-back distance, and the camera is stated to accept an F-mount lens through an adapter. Optical coverage must suit the 8192-pixel line.

What are the environmental and mechanical bounds of MV-CL086-B0F1C?

The camera measures 76 mm × 76 mm × 66.3 mm and weighs about 465 g. It is rated IP40 after correct lens installation and wiring, with operation from –20 °C to 55 °C and 5% RH to 90% RH without condensation.