Hikrobot MV-CS060-10GM-PRO

Applications and position in the range

Monochrome inspection at 3072 × 2048 is the operating point of the MV-CS060-10GM-PRO. Its 6.3 MP Sony® IMX178 CMOS sensor uses a rolling shutter, 2.4 µm pixels and a 1/1.8-inch optical format. Full-resolution acquisition reaches 19.1 fps over Gigabit Ethernet, placing emphasis on spatial sampling and network integration rather than rapid sequences. A 71.3 dB dynamic range and exposure adjustment from 25 µs to 2.5 sec cover changing illumination levels.

The mono output suits dimensional checks, edge analysis, alignment and surface-contrast inspection where color separation is unnecessary. PoE can carry power with the Ethernet connection, while a 9 VDC to 24 VDC input is available through the 6-pin Hirose power and I/O connector. One opto-isolated input, one opto-isolated output and one bidirectional non-isolated line support coordination with equipment. The 29 mm × 29 mm body face and C-mount suit compact stations.

Within this group, MV-CS060-10UM V5.0 and MV-CS060-10UM-PRO keep the same 3072 × 2048 mono format but reach 60.9 fps through USB 3.0; select either when the host is close to the camera and the higher rate matters. MV-CS060-10GC stays with Gigabit Ethernet and 19.1 fps but records color. Move to MV-CS120-10GM V5.0 when 4024 × 3036 mono detail is more important than the higher frame rate offered here.

Specifications

Selection and applications

Monochrome dimensional inspection at 3072 × 2048. PoE-connected edge and alignment analysis. Controlled-motion surface-contrast imaging at 19.1 fps.

Minimum kit: MV-CS060-10GM-PRO camera, a C-mount lens, a Gigabit Ethernet cable, and either PoE or a 9 VDC to 24 VDC supply through the 6-pin Hirose connector form the minimum operating set.

Nearby in the range: MV-CS060-10UM V5.0 — Prefer it for 60.9 fps mono acquisition through USB 3.0.; MV-CS060-10GC — Prefer it when color output is required with Gigabit Ethernet at 19.1 fps.; MV-CS120-10GM V5.0 — Prefer it for 4024 × 3036 mono imaging over Gigabit Ethernet..

Cables and accessories for this model

Compatibility per manufacturer data.

Data cables

GigE

I/O & power cables

Hirose 6-pin IO

Power

Power

Mounting

Camera mounts

All accessory families →

FAQ

What motion profile suits the rolling shutter and 19.1 fps rate?

The Sony® IMX178 uses a rolling shutter and delivers 19.1 fps at 3072 × 2048. Use it where the scene can remain sufficiently stable during exposure, or where motion is controlled by the station. Exposure can be set from 25 µs to 2.5 sec to balance blur and available light.

Can power and image data share the Gigabit Ethernet connection?

Yes. The camera supports PoE on its Gigabit Ethernet interface, so one network connection can carry image data and power. A separate 9 VDC to 24 VDC supply is also supported through the 6-pin Hirose connector when the installation uses external power and I/O wiring.

How should a C-mount lens be matched to this mono sensor?

Choose a C-mount lens that covers the 1/1.8-inch sensor format and resolves the 2.4 µm pixel pitch across 3072 × 2048 pixels. The lens installation also forms part of the stated IP40 condition, so its mechanical fit and the associated wiring should be completed correctly.

Which electrical lines are available for station integration?

The 6-pin Hirose connector provides one opto-isolated input on Line 0, one opto-isolated output on Line 1 and one bidirectional non-isolated connection on Line 2. The same connector accepts the 9 VDC to 24 VDC external supply when PoE is not used.

What ambient limits apply to an enclosed inspection station?

The working range is –30 °C to 60 °C, with storage from –30 °C to 70 °C. Permitted humidity is 20% RH to 95% RH without condensation. The enclosure rating is IP40 when the lens is properly installed and wiring is complete, so the station must account for the actual exposure to dust and liquids.