Hikrobot MV-CS120-10GM V5.0

Monochrome detail over Gigabit Ethernet

Fine monochrome sampling with a network interface characterizes the MV-CS120-10GM V5.0. A 12.2 MP Sony® IMX226 rolling-shutter CMOS sensor generates 4024 × 3036 Mono 8 frames at up to 10 fps. Its 1/1.7-inch active format has 1.85 µm pixels and a dynamic range of 69.4 dB. Exposure extends from 33 µs to 2 sec, while the data link is 1000 Mbit/s Gigabit Ethernet with 100 Mbit/s Fast Ethernet operation also supported.

The mono output supports dimensional measurement, contour analysis and inspection of small contrast features where color is not required. PoE can combine the network data path with power; an external 9 VDC to 24 VDC source may instead enter through the 6-pin P7 connection. That connector also carries one opto-isolated input, one opto-isolated output and one bidirectional non-isolated I/O. The 29 mm × 29 mm × 42 mm housing accepts C-mount lenses.

MV-CS120-10GC V5.0 uses the same 4024 × 3036, 10 fps and Gigabit Ethernet platform but records Bayer RG 8 color. MV-CS120-10UM V5.0 remains mono and raises the full-resolution rate to 29.4 fps by moving to USB 3.0. For more pixels with the same network type, MV-CS200-10GM reaches 5472 × 3648 at 5.9 fps; choose it when spatial sampling is more important than the 10 fps ceiling.

Specifications

Selection and applications

Networked mono measurement at 4024 × 3036. PoE contour analysis at 10 fps. Inspection of small contrast features with 1.85 µm pixels.

Minimum kit: MV-CS120-10GM V5.0 camera, a C-mount lens, a Gigabit Ethernet cable, and either PoE or a 9 VDC to 24 VDC supply through the 6-pin P7 connector form the minimum operating set.

Nearby in the range: MV-CS120-10GC V5.0 — Prefer it when Bayer RG 8 color is needed at the same 4024 × 3036 and 10 fps.; MV-CS120-10UM V5.0 — Prefer it for 29.4 fps mono acquisition through USB 3.0.; MV-CS200-10GM — Prefer it when 5472 × 3648 mono sampling outweighs its lower 5.9 fps maximum..

Cables and accessories for this model

Compatibility per manufacturer data.

Data cables

GigE

I/O & power cables

Hirose 6-pin IO

Power

Power

Mounting

Camera mounts

All accessory families →

FAQ

What Mono 8 output is available on the Gigabit Ethernet link?

The maximum listed operating point is 10 fps at 4024 × 3036 in Mono 8. The link runs at 1000 Mbit/s Gigabit Ethernet and can also operate with 100 Mbit/s Fast Ethernet. The sensor is the 12.2 MP Sony® IMX226 with 1.85 µm pixels.

Which power and I/O routes are available for machine wiring?

PoE can supply the camera over Ethernet. Alternatively, the 6-pin P7 connector accepts 9 VDC to 24 VDC and provides one opto-isolated input, one opto-isolated output and one bidirectional non-isolated line. Typical consumption is stated as 1.5 W at 12 VDC.

How should a lens be chosen for 1.85 µm mono pixels?

Use a C-mount lens that covers the 1/1.7-inch sensor and supports the detail required from 1.85 µm pixels over 4024 × 3036. Monochrome output removes the need to preserve hue, but the optical setup still has to transfer the contrast used for measurement or edge analysis.

What are the operating and storage temperature boundaries?

The specified working interval is –30 °C to 60 °C, and the storage interval is –30 °C to 80 °C. Relative humidity may be 20% RH to 95% RH without condensation. IP40 applies with correct lens installation and wiring, so the surrounding protection should follow the station environment.

How does MV-CS200-10GM trade speed for additional sampling?

MV-CS200-10GM increases mono resolution from 4024 × 3036 to 5472 × 3648 and changes the sensor from Sony® IMX226 to Sony® IMX183. Both use Gigabit Ethernet and PoE. Its maximum is 5.9 fps, compared with 10 fps for MV-CS120-10GM V5.0.