Hikrobot MV-DP3020-01P V2.0

Short-range micro-profiling at up to 46.7 kHz

MV-DP3020-01P V2.0 measures a 6.8 mm Z range around a 21.4 mm reference distance. Its X field is 14 mm near, 14.3 mm at reference and 14.6 mm far, and each profile contains 3200 points. Z resolution is 0.71 to 0.78 µm, and Z repeatability is 0.22 µm, obtained on gauge blocks in a laboratory as an average of 4096 tests.

This close-working geometry suits fine height, edge and narrow-surface checks. In high frame rate mode the scan rate spans 3.4 to 46.7 kHz, so the profile pitch along the part follows from the selected rate and the motion speed. Software or differential-encoder hardware triggering is supported; profile, depth and brightness outputs use Gigabit Ethernet, and the 12-pin M12 interface carries 24 VDC and machine I/O.

MV-DP2020 shares the 6.8 mm Z range, 21.4 mm reference distance and 0.22 µm repeatability, but its high-frame-rate range ends at 23.9 kHz rather than 46.7 kHz. MV-DP4020-01P narrows the Z range to 5.2 mm, increases profile count to 4080 and states 0.15 µm repeatability. Choose MV-DP3020-01P V2.0 when the same compact geometry must be scanned at up to 46.7 kHz with 3200 points per profile.

Documents

Selection and applications

Fine height profiling through a 6.8 mm Z range. Narrow-field 3200-point edge and contour capture. Encoder-triggered acquisition at up to 46.7 kHz.

Minimum kit: MV-DP3020-01P V2.0, a Gigabit Ethernet cable, a 12-pin M12 power and I/O cable matched to the configuration, and a 24 VDC supply form the minimum acquisition kit.

Nearby in the range: MV-DP2020 — Prefer it for a single 6.8 mm range definition and rates from 1.7 to 23.9 kHz; MV-DP4020-01P — Prefer it for 4080 points and 0.15 µm repeatability within a 5.2 mm Z range.

Cables and accessories for this model

Compatibility per manufacturer data.

Data cables

GigE

I/O & power cables

12-pin IO

Power

Power

Other

3D accessories

All accessory families →

FAQ

What measurement envelopes are listed for MV-DP3020-01P V2.0?

The Z range is 6.8 mm around a 21.4 mm reference distance. X coverage is 14 mm at the near limit, 14.3 mm at the reference distance and 14.6 mm at the far limit, so fixtures and part travel are checked against that whole envelope.

What repeatability and Z resolution does MV-DP3020-01P V2.0 provide?

Z repeatability is 0.22 µm, measured on gauge blocks in a laboratory as an average of 4096 tests. Z resolution is 0.71 to 0.78 µm, Z linearity is ±0.01% of the measurement range, and each 3200-point profile has a transverse interval of 4.38 to 4.67 µm.

Which profile scan rates can MV-DP3020-01P V2.0 provide?

In high frame rate mode the scan rate is 3.4 to 46.7 kHz. The output remains 3200 points per profile; the spacing between successive profiles along the part follows from the selected rate and the motion speed.

How can MV-DP3020-01P V2.0 synchronize acquisition with motion?

Trigger methods include software trigger and hardware trigger from a differential encoder. The 12-pin M12 interface provides power and I/O: two opto-isolated inputs (Line 0/9), two differential inputs (Line 3/6) and one differential output (Line 1).

Which output types and Ethernet rates are listed for this V2.0 sensor?

The sensor produces profile data, depth images and brightness images. Transmission uses 1000 Mbit/s Gigabit Ethernet, with compatibility for 100 Mbit/s Fast Ethernet when that link rate fits the selected profile stream.

What power, enclosure and ambient limits apply to MV-DP3020-01P V2.0?

The 139.5 × 111.5 × 60.5 mm housing weighs approximately 1075 g and is rated IP67. Supply is 24 VDC, with typical consumption of 17.2 W at 24 VDC. The working temperature is 0 to 45 °C and humidity is 20 to 85% RH without condensation.